Purdue University Graduate School
Browse
Dissertation.pdf (3.79 MB)

Modeling and Measurement of Dust Dispersion Patterns in Confined Spaces

Download (3.79 MB)
thesis
posted on 2020-08-05, 18:54 authored by Yumeng ZhaoYumeng Zhao

In the grain handling and processing industry, dust emission and accumulation are major concerns for the safety of workers and for explosion risks. Dust emission and accumulation locations highly depend on the facility design and equipment used for handling and processing. To prevent an explosive atmosphere, monitoring the amount of dust accumulated or dispersed is extremely important. However, methods of measuring the dust concentration require the installation of equipment. The Occupational Safety and Health Administration (OSHA) regulations and National Fire Protection Association (NFPA) standards restrict the thickness of dust layers on floors for fine powder materials such as starch. The objective of this dissertation was to better understand the rate of dust layer accumulation, dust suspension patterns, and the optical properties of suspended dust. For this purpose, The Discrete Phase Model (DPM) was combined with a Computational Fluid Dynamics Model (CFD) and the hybrid model was used to model dust dispersion. Dust dispersion patterns under pressure, such as primary explosions or leakage from equipment, were simulated using the unsteady CFD-DPM approach. The particle-wall interaction based on energy conservation was also introduced in this model. Both one-time and continuous dust dispersion in an enclosed chamber were simulated to mimic secondary explosions and the dust emission from processing equipment. In addition, the light extinction property of suspended dust was studied as a method of measuring suspended dust concentration.

For a one-time dust dispersion incident, the predicted dust concentration agreed with the simulation result for the trial conducted at a dust injection velocity of 2 m/s with injection rates of 0.05 and 0.10 kg/m³ and at a dust injection velocity of 10 m/s with an injection rate of 0.05 kg/m³. The dust concentration in the entire chamber increased with dust injection velocity and the mass of injected dust. As dust injection velocity increased, dust spread out and formed a larger explosive dust cloud. However, the dust concentration inside the chamber was non-uniform. Considering the minimum explosive concentration, the largest explosive cloud was created at a dust injection velocity of 10 m/s with an injection rate of 0.10 kg/m³. Explosive concentrations of dust were found somewhere in the chamber for all dispersion rates. At an injection velocity of 10 m/s with an injection rate of 0.10 kg/m³, the predicted dust concentration was 10% more than the measured dust concentration. Thus, this model is suitable for dilute dust particle dispersion flows, where the volume fraction of particles is less and only a single particle layer settles.

Continuous dispersion was simulated to determine the suspended dust concentration and particle deposition patterns. Dust was dispersed for 30 s at dispersion rates of 2, 4 and 6 g/min at a dust injection velocity of 2 m/s. The dust concentration increased at a constant rate after a few seconds of dispersion, regardless of the dust dispersion rate. Most dust particles were deposited near the dust dispersion nozzle. Large particles were more affected by gravitational force and inertia compared with small particles, which traveled with airflow and settled behind the nozzle. The dust accumulated close to the dispersion nozzle faster than behind the nozzle location. However, specific attention must be paid to small particles, because they are more likely to cause an explosion, as their minimum explosive concentration is lower than that of large particles.

The light extinction coefficients of cornstarch, grain dust, and sawdust were measured using a two-target method. The suspended dust concentration was measured using a calibrated laser instrument. The light extinction coefficient was linearly related to the suspended dust concentration. The correlation coefficient between the light extinction coefficient and suspended dust concentration depended on particle size, particle shape, and chemical properties.

Controlling dust cloud generation and minimizing the concentration and volume of dust clouds are some key measures to prevent dust explosions. The mathematical models developed in this study to predict dust dispersion, suspension, and rate of settling will help solve a few of the challenges in the particulate material handling and processing industry. This method of measuring the light extinction coefficient can be applied development of a dust safety monitoring system. The result presented in this dissertation will help the industry prevent the formation of an explosive atmosphere.


History

Degree Type

  • Doctor of Philosophy

Department

  • Agricultural and Biological Engineering

Campus location

  • West Lafayette

Advisor/Supervisor/Committee Chair

Dr. R.P. Kingsly Ambrose

Additional Committee Member 2

Dr. Richard L. Stroshine

Additional Committee Member 3

Dr. Albert J. Heber

Additional Committee Member 4

Dr. Carl R Wassgren

Usage metrics

    Licence

    Exports

    RefWorks
    BibTeX
    Ref. manager
    Endnote
    DataCite
    NLM
    DC